InMode Error Codes and Fault Messages
Service Resource / Error Codes / InMode
Use this reference to identify documented fault categories and prepare a service request. Match the console, handpiece, software, and manual revision before interpreting a code. A fault is a diagnostic clue, not a confirmed failed component.
Scope: Older InMode II, Optimas and Triton-family documentation, plus the RF/Morpheus8 revisions named below. This is not a complete reference for every InMode generation.
System and RF
Optimas Operator Manual DO608395A, February 2019
H8002 — Handpiece connection not detected
H8005 / H800F / H8010 — System memory fault
H800E — Incompatible software
H8003 / H8006 / H8007 — RF fault group
H8601 — Distributor-card connection
H8609 — Water temperature
Lumecca and IPL
System Service Manual DO606737A Rev B
H8401 — IPL-board communication
H8410 — Handpiece temperature outside limits
H8420 / H8421 — Bottom / top switch fault
H8422 — Ignition failure
H8423 — Conduction failure
H8430 / H8431 — Capacitor charging / discharge failure
H8481 — Corrupted IPL-board information
Diolaze and laser
DO606737A Rev B; H8210/H8211: operator-level grouping only
H8201 — Laser-board communication
H8202 — Handpiece temperature outside limits
H8210 / H8211 — Laser fault group; specific meaning not established here
H8220 / H8221 / H8222 / H8223 / H8224 / H8225 / H8226 / H8227 / H8228 / H8229 / H822A / H822C / H822D / H822E / H822F — Handpiece motion/enable faults
H8232 / H8233 — Laser-enable switch faults
Laser driver electrical faults
System Service Manual DO606737A Rev B
H8300 — Low 48 V supply
H8301 — Board startup failure
H8302 — Unstable output current
H8303 / H8304 — Low / high diode voltage
H8305 / H8306 — Low / high output current
H8307 — Hardware overcurrent
H8309 — Input overcurrent protection
H830A / H830B — Low / high input voltage
H830C / H830D — Low / high system voltage
H830E — Excessive requested current
H830F — Low voltage after startup
H8311 — Input pulse limit exceeded
H8312 — Absolute output overcurrent
H8313 — Voltage startup-test failure
H8314 / H8315 — Upper / lower MOSFET short
H8381 — Corrupted laser-board information
Cooling and water flow
System Service Manual DO606737A Rev B
H8608 — Low active pump current
H860B — High active pump current
H860F — Cooling enabled in disabled state
Morpheus8 motion faults
RF Service Manual DO606153A Rev B, December 2018
H8A23 — Motor acceleration/stall fault
H8A2D — Motor-driver overcurrent or overtemperature
H8AA5 — Motor constant-speed travel/stall fault
Software messages
RF Service Manual DO606153A Rev B
Software Plug Missing — Software plug absent or improperly connected
Software Start Error — Operating-system startup error
Checksum Error — Software integrity/loading problem
Important interpretation notes
H8007 is grouped as RF-related in the Optimas operator manual; RF Service Manual DO606153A Rev B calls it a temperature-sensor fault. H860B does not by itself establish a failed pump. Diagnosis must establish the cause.
H8240 remains unverified. Do not extend these definitions automatically to Optimas Max, EmpowerRF, IgniteRF, Evolve X, Envision, or newer software.
Before requesting service
Record the complete screen message, model and serial number, software version, handpiece, when the fault occurs, recent changes, and checks already completed. Keep patient identifiers out of photos. Follow the exact operator manual. Persistent or suspected safety faults require assessment before treatment resumes. Internal electrical work belongs with qualified service personnel.
Request equipment service | 833-286-7669
Reference documents
Optimas Operator Manual DO608395A — troubleshooting, printed pages 75–76.
System Service Manual DO606737A Rev B — Section 7.
RF Service Manual DO606153A Rev B — Section 7.
Reviewed November 6, 2026. VMS is an independent service provider and is not affiliated with or endorsed by InMode. Manufacturer names identify equipment only. This reference does not replace the instructions supplied with your device.